01-31-2011, 02:56 PM | #1387 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
Good like i posted on non 2SS or 2LT cars GM made changes to the harness in the dash so i have to do a more expansive harness for them.
|
01-31-2011, 03:04 PM | #1388 |
Whipped
|
I'm really worried about not putting the hold in the dash right. . .
__________________
|
01-31-2011, 03:12 PM | #1389 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
Don't be, all you do is start past the line on the dash 1/4 past it and use the template i gave you its smaller then the opining, from there you will need to make it biger to the sides and windshield.
|
01-31-2011, 05:48 PM | #1390 |
Drives: 2010 2SS Join Date: Apr 2010
Location: Washington
Posts: 677
|
My steering wheel came right off , no puller was needed. I left the bolt in with a few threads and yanked on the wheel.
|
02-01-2011, 08:45 AM | #1391 |
Whipped
|
I'll give it a little tug today to see if it will come off.
Working on another mod also. Well 3 at once... HUD install, seat stitching dying, and a LED light in the over head console. The wifes's HHR has one that stays on the whole time. Very nice... I have a extra OEM blue one.
__________________
|
02-01-2011, 10:11 AM | #1392 |
Drives: 2016 2SS, SW Join Date: Oct 2009
Location: Chicago Suburbs
Posts: 1,079
|
Keep us posted on the LED in the over-head console!
|
02-01-2011, 10:59 AM | #1393 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
I Did this to the home link with 3MM LED's.
|
02-01-2011, 11:15 AM | #1394 |
Drives: 2016 2SS, SW Join Date: Oct 2009
Location: Chicago Suburbs
Posts: 1,079
|
Cool! My plan is for a general down-light. Is there info on pulling that panel?
|
02-01-2011, 11:56 AM | #1395 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
Do you mean the center top counsel? if so here you go.
This will help you out the pic are gone but the info is there. http://www.camaro5.com/forums/showpo...93&postcount=1 |
02-01-2011, 12:00 PM | #1396 |
Drives: 2016 2SS, SW Join Date: Oct 2009
Location: Chicago Suburbs
Posts: 1,079
|
Hmm. Link no good.
|
02-01-2011, 12:35 PM | #1397 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
|
02-01-2011, 01:21 PM | #1398 |
Whipped
|
I should just mail mine to ya. I like that idea, but it's a little to advanced for me.
__________________
|
02-01-2011, 02:00 PM | #1399 |
Drives: 2016 2SS, SW Join Date: Oct 2009
Location: Chicago Suburbs
Posts: 1,079
|
Thanks Ofer!
|
02-01-2011, 03:33 PM | #1400 | |
Drives: aqua 2ss l99 Join Date: Jun 2009
Location: Edmonton
Posts: 1,215
|
Quote:
another tip....ofer's template fits the bezel perfect, so you can go up to about an extra 1/8th inch or so past and the clips will still snap in and hold. i put the bezel on the projector lens, placed the projector in the dash, and traced the inside of the bezel on the inside of the dash. i used a grease pencil and traced ofer's template on the outside and measured both to the outside of the dash and they didnt line up--so i knew it was wrong. on the inside i drilled 4 eigth inch holes from the inside out to see where they would show to my outside markings. then i bolted the projector in place, and shone a light inside to see how far left and right i had to cut and i just moved ofers template accordingly and made sure i lined up to the dash bodyline. i was worried about getting it just right and perfectly centered to the lens. i cut my final hole with a olfa knife in 3 stages being carefull to not slip and make a mark or weak spot in dash. once satisfied, i filed the edges super smooth and round filed the corners so the dash doesnt crack in the years to come. hope this helps.
__________________
May your exhaust note, sing in harmony with your blower.
|
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New Camaro Exterior and Interior Stainless Steel Trim Parts from RPI Designs! | RPI Designs | Cosmetics and Lighting Modification Discussions | 36 | 04-02-2020 05:32 PM |
February 2010 Camaro production & sales figures. Tops Mustang for 9th straight month! | Tran | 5th Gen Camaro SS LS LT General Discussions | 52 | 03-03-2010 09:39 PM |
DEALER ONTARIO CANADA WE SHIP ANYWHERE IN CANADA 2010 CAMAROS FOR SALE IN STOCK NOW! | dz | Dealer Camaros for Sale | 0 | 03-03-2010 05:43 PM |
Zex Nitrous System for 2010 Camaro SS @ BMC Performance! | Kris@BMCPerformance | Forced Induction | 2 | 02-18-2010 06:59 PM |
2010 Chevrolet Camaro makes finalist list for 2010 World Car Design of the Year | Tran | 5th Gen Camaro SS LS LT General Discussions | 37 | 02-17-2010 04:22 PM |