Add HUD to your 2010 - Page 98 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

2SSRS@Gen5diy · 01-10-2011, 07:51 PM

I may have made a mistake in one wire there are two Green wires and i did it ones.

patrickt · 01-10-2011, 09:14 PM

Got a new shipment of HUDs in so we got plenty to got around still 471.53 for the complete kit of hud trim switch and hardware Here is a link to order or you can give me a call https://www.paypal.com/cgi-bin/websc...=LWFF6MFFFP3KG

hot ss · 01-11-2011, 12:07 PM

i pulled the guage pack and bench tested mine before gutting the car....
all is well, thx Ofer for tyeh quality harness.
literally is plug and play. even radio track shows up on it... neatto Mosquito!

hot ss · 01-11-2011, 12:24 PM

one more thing, upon review of this thread and subsequent pictures of the dash underbelly....
has anyone tried setting the hud in place and poking thru the dash to make
guides for Ofer's pattern. i for one want the trim bezed lined up perfect.
seems there is too much room for error going from the top..... no offence.

Cam 427 · 01-11-2011, 02:49 PM

Quote:

Originally Posted by hot ss

one more thing, upon review of this thread and subsequent pictures of the dash underbelly....
has anyone tried setting the hud in place and poking thru the dash to make
guides for Ofer's pattern. i for one want the trim bezed lined up perfect.
seems there is too much room for error going from the top..... no offence.

Take a look at post 1343. The pictures look like production HUD installation. I looked a car at a dealer and that is what it looks like. Also, I took some measurements and measured 9 inches from the left edge of the dash to the left edge of the HUD trim bezel. So, with the cut line suggested in post 1343, it should be close. Mine turned out good.
You could use these parameters and drill small holes well within the boundries and go out from those as needed. Good luck.

thebrainhart · 01-12-2011, 12:51 AM

Yeah, when I cut mine, I lined up Ofer's template, put marks where the cutout goes, then made a small box inside and went from there.
I often placed the HUD into place, to see which sides I needed to cut out more.
When I was almost there, I'd install the bezel and the HUD and see how things looked, making sure it was parallel, and about 1/4" away from the ledge on the dash.
If it was a little too small, it'd bend the bezel a bit, so I'd know where to cut some more off.
Patience pays off.

I still don't have it all back together yet, work has picked up, so I only get a few minutes here and there, but its mostly done but the center console. I started it up tonight, turned the switch on, and was amazed by the beauty!

Thanks again to Ofer and everybody who helped make this possible!

Top Thrill · 01-15-2011, 09:03 PM

I am very surprised the mod is not more popular that this. Only 14 installed?

2SSRS@Gen5diy · 01-15-2011, 09:15 PM

I sold some 40 harness so far but some ppl are ......................

WCoolBreeze · 01-16-2011, 12:41 AM

Those who have installed the HUD to their car, sent me your infor and I will add you to the list. This means that 26 people need to send their infor to Me.

Walt B.

thebrainhart · 01-16-2011, 12:52 AM

Just added my info to that thread.
I had to search for it, but I found it. Its here: http://www.camaro5.com/forums/showthread.php?t=117696

phenixdragon · 01-16-2011, 03:35 PM

Quote:

Originally Posted by Top Thrill

I am very surprised the mod is not more popular that this. Only 14 installed?

I'd have it installed myself but I'm in the process of buying my first home and buying it months earlier then what I was planning so I need to save every penny for my down payment. But once we close in a few weeks, I plan on doing this. The dash is pretty useless to me, I can't really see it with my left hand/arm blocking the center of it and the wheel blocking the rest of it. Would be nice to have a HUD so I can see my speed without having to move my hand/arm.

Jayhawk500 · 01-16-2011, 04:21 PM

I have one of those harnesses from Ofer.
The only problem is...The bills come first!
I'll install hopefully by the end of the summer.

ShadoChaser · 01-16-2011, 07:15 PM

I have one of his harnesses, Just saving up for the HUD Assembly, then to install it

ckaram · 01-16-2011, 07:46 PM

Quote:

Originally Posted by 2SSRS

I sold some 40 harness so far but some ppl are ......................

I'm one of those guys who is chicken s**t!

I bailed on the idea. Anyone want the harness? Same fee as 2SSRS unless you want it back, 2SS? PM me. Sorry to hijack.

01-11-2011, 12:07 PM	#1361
hot ss Drives: aqua 2ss l99 Join Date: Jun 2009 Location: Edmonton Posts: 1,215	i pulled the guage pack and bench tested mine before gutting the car.... all is well, thx Ofer for tyeh quality harness. literally is plug and play. even radio track shows up on it... neatto Mosquito! __________________ May your exhaust note, sing in harmony with your blower.

01-11-2011, 12:24 PM	#1362
hot ss Drives: aqua 2ss l99 Join Date: Jun 2009 Location: Edmonton Posts: 1,215	one more thing, upon review of this thread and subsequent pictures of the dash underbelly.... has anyone tried setting the hud in place and poking thru the dash to make guides for Ofer's pattern. i for one want the trim bezed lined up perfect. seems there is too much room for error going from the top..... no offence. __________________ May your exhaust note, sing in harmony with your blower.

01-12-2011, 12:51 AM	#1364
thebrainhart Drives: '10 Camaro 2SS/RS CGM LS3 A6 Join Date: May 2009 Location: Bountiful, UT Posts: 683	Yeah, when I cut mine, I lined up Ofer's template, put marks where the cutout goes, then made a small box inside and went from there. I often placed the HUD into place, to see which sides I needed to cut out more. When I was almost there, I'd install the bezel and the HUD and see how things looked, making sure it was parallel, and about 1/4" away from the ledge on the dash. If it was a little too small, it'd bend the bezel a bit, so I'd know where to cut some more off. Patience pays off. I still don't have it all back together yet, work has picked up, so I only get a few minutes here and there, but its mostly done but the center console. I started it up tonight, turned the switch on, and was amazed by the beauty! Thanks again to Ofer and everybody who helped make this possible! Attached Images __________________ - 2010 Camaro 2SS/RS CGM LS3 A6 "Lurch" - FLYNGSS - Some ProCharger, Alky, CompCams, Brian Tooley, Holley, Livernois, K&N, Ridetech, DSS, Kooks, JDP Motorsports, Pfadt, BMR, Prothane, Weld, M&H, Mickey Thompson, RKSport, Elite, Garys, Defenderworx, Anvil, etc.

01-15-2011, 09:03 PM	#1365
Top Thrill BOD 5/28/09 #13485 Drives: 2010 Camaro 2LT RS Join Date: Jan 2009 Location: Chesapeake, Virginia Posts: 913	I am very surprised the mod is not more popular that this. Only 14 installed? __________________

01-16-2011, 12:41 AM	#1367
WCoolBreeze 2SS Drives: 2016 2SS, Red Garnet Tint Join Date: Nov 2008 Location: Imperial, CA Posts: 1,343	Those who have installed the HUD to their car, sent me your infor and I will add you to the list. This means that 26 people need to send their infor to Me. Walt B. __________________ 2016 Camaro 2SS 2005 Dodge Magnum R/T (Yes it has a Hemi) 1987 Camaro RS (California Special) - For Sale Gen6, 2016 Camaro 2SS, Red Garnet Tint (with Silver Rally Stripes) Ordered: 2-12-2016 TPW: 3-7-2016 Built: 3-7-2016 VIN 1G1FH78G0157626 Delivered: 4-26-2016

01-10-2011, 07:51 PM	#1359
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	I may have made a mistake in one wire there are two Green wires and i did it ones.

01-10-2011, 09:14 PM	#1360
patrickt Drives: still saving! Join Date: Feb 2010 Location: Reading, PA Posts: 6,227	Got a new shipment of HUDs in so we got plenty to got around still 471.53 for the complete kit of hud trim switch and hardware Here is a link to order or you can give me a call https://www.paypal.com/cgi-bin/websc...=LWFF6MFFFP3KG

01-15-2011, 09:15 PM	#1366
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	I sold some 40 harness so far but some ppl are ......................

01-16-2011, 12:52 AM	#1368
thebrainhart Drives: '10 Camaro 2SS/RS CGM LS3 A6 Join Date: May 2009 Location: Bountiful, UT Posts: 683	Just added my info to that thread. I had to search for it, but I found it. Its here: http://www.camaro5.com/forums/showthread.php?t=117696 __________________ - 2010 Camaro 2SS/RS CGM LS3 A6 "Lurch" - FLYNGSS - Some ProCharger, Alky, CompCams, Brian Tooley, Holley, Livernois, K&N, Ridetech, DSS, Kooks, JDP Motorsports, Pfadt, BMR, Prothane, Weld, M&H, Mickey Thompson, RKSport, Elite, Garys, Defenderworx, Anvil, etc.

01-16-2011, 04:21 PM	#1370
Jayhawk500 Drives: 2010 Camaro SS/RS Join Date: Apr 2009 Location: Warrenton, Or. Posts: 1,062	HUD Install I have one of those harnesses from Ofer. The only problem is...The bills come first! I'll install hopefully by the end of the summer. __________________ Jayhawk500 2010 2SS/RS, Six speed, Rally Yellow w/ Black Painted Stripes, Boston Acoustic Stereo, Polished 20" wheels, Solo Mach X Catback Exhaust, Solo HF Cats, Halltech CAI, Full Dash & Door ABL, ABL Lit Homelink Buttons, HUD Installed, Ride Tunes, Full Electric Passenger Seat, Fbodfather signed, VIN # 4492, PAID OFF!!! 2010 Yellow 2SS/RS with black painted Stripes...$37,000.00; Ride Tones sound system and remote...$ 40.00; Seeing the kids faces (Young and Old) light up and almost wet their pants....Priceless!!!

01-16-2011, 07:15 PM	#1371
ShadoChaser Gamer & Ghosthunter! Drives: 2010 GCN 2SS/RS L99 Join Date: Jan 2010 Location: Fort Worth, Tx Posts: 312 View My Garage	I have one of his harnesses, Just saving up for the HUD Assembly, then to install it __________________ Ceramic Window Tints (35%), gen5diy MyLink w/Nav, Roto-Fab CAI, Rivercity Painted Emblems

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Camaro Exterior and Interior Stainless Steel Trim Parts from RPI Designs!	RPI Designs	Cosmetics and Lighting Modification Discussions	36	04-02-2020 05:32 PM
February 2010 Camaro production & sales figures. Tops Mustang for 9th straight month!	Tran	5th Gen Camaro SS LS LT General Discussions	52	03-03-2010 09:39 PM
DEALER ONTARIO CANADA WE SHIP ANYWHERE IN CANADA 2010 CAMAROS FOR SALE IN STOCK NOW!	dz	Dealer Camaros for Sale	0	03-03-2010 05:43 PM
Zex Nitrous System for 2010 Camaro SS @ BMC Performance!	Kris@BMCPerformance	Forced Induction	2	02-18-2010 06:59 PM
2010 Chevrolet Camaro makes finalist list for 2010 World Car Design of the Year	Tran	5th Gen Camaro SS LS LT General Discussions	37	02-17-2010 04:22 PM