Alignment Help Thread - Page 28 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

ZWA SS · 03-30-2015, 05:20 PM

Quote:

Originally Posted by JusticePete

Front Camber -1.00
Front Toe 0.00
Rear Toe IN 1/8"
Rear Camber -0.50

Thank you.
Is the 1/8" rear tie per wheel I assume?

ZWA SS · 03-30-2015, 08:35 PM

Quote:

Originally Posted by JusticePete

Front Camber -1.00
Front Toe 0.00
Rear Toe IN 1/8"
Rear Camber -0.50

Thank you.
-1.00 and -.50 are degrees, correct?
Just want to make sure to avoid any confusion.

Norm Peterson · 03-31-2015, 05:58 AM

As far as I know, camber specs have always been expressed in degrees.

Norm

ZWA SS · 03-31-2015, 07:15 AM

Quote:

Originally Posted by Norm Peterson

As far as I know, camber specs have always been expressed in degrees.

Norm

Thank you.
I assumed, but you know what happens when you assume..

JusticePete · 03-31-2015, 07:43 AM

yep, degrees.

Rob@WretchedMS · 03-31-2015, 09:40 AM

Quote:

Originally Posted by ZWA SS

Thank you.
Is the 1/8" rear tie per wheel I assume?

Total toe, 1/16" per side

ZWA SS · 04-03-2015, 12:57 PM

The front wheels he said would rub the springs if set to negative. And the rear camber he couldn't get to -.50 on one side for some reason so I had him match the other side.
I'm not sure if I should look I to other wheels/offset or suspension. Don't think a spacer on the front is what I want to do.
Help..

Destructo09 · 04-03-2015, 01:23 PM

Yeah, those +35 offset 20x10s are probably going to limit your front camber a good bit, I have plenty of clearance with a 20x9 +40mm + a 5mm spacer and i'm running -2.1, it was really close without the 5mm spacer but didn't rub.

a 20x9 +35mm setup would be able equal backspace wise to a 20x10 +23mm. SO a +35mm is going to be a good bit closer I suspect.

ZWA SS · 04-03-2015, 04:35 PM

How much spacer would I need?
Never shopped for them

ZWA SS · 04-03-2015, 11:16 PM

I realize now they did .125" per side vs total toe on the rear. It's all a mess.

JusticePete · 04-04-2015, 09:41 AM

What is your ride height?

ZWA SS · 04-04-2015, 07:56 PM

28 3/16 front
28 1/4 rear.

Raising wouldn't bother me any.

JusticePete · 04-05-2015, 09:58 PM

Quote:

Originally Posted by ZWA SS

28 3/16 front
28 1/4 rear.

Raising wouldn't bother me any.

Are you measuring from the bottom lip of the rim, up through the wheel center to the painted edge of the fender?

20" wheels, correct?

ZWA SS · 04-06-2015, 01:34 AM

I measured from fender edge to the ground thru the centerline of the wheel.

04-03-2015, 12:57 PM	#385
ZWA SS BowtieBelle's SS Drives: 2010 Camaro SS Join Date: Jan 2012 Location: Perry, ok Posts: 1,074	The front wheels he said would rub the springs if set to negative. And the rear camber he couldn't get to -.50 on one side for some reason so I had him match the other side. I'm not sure if I should look I to other wheels/offset or suspension. Don't think a spacer on the front is what I want to do. Help.. __________________ My Z/SS http://www.camaro5.com/forums/showthread.php?t=286858 .

04-03-2015, 01:23 PM	#386
Destructo09 Drives: 2010 CGM Camaro 2SS/LS3 Join Date: Oct 2013 Location: Raleigh-Durham Posts: 1,409	Yeah, those +35 offset 20x10s are probably going to limit your front camber a good bit, I have plenty of clearance with a 20x9 +40mm + a 5mm spacer and i'm running -2.1, it was really close without the 5mm spacer but didn't rub. a 20x9 +35mm setup would be able equal backspace wise to a 20x10 +23mm. SO a +35mm is going to be a good bit closer I suspect. __________________ 2010 2SS BMR 1" Springs Koni Orange struts/shocks 1LE rear sway bar SRP Racing Pedals Hurst Billet short shifter Square tire/wheel setup Elite Engineering Catch Can Stainless Power longtubes/highflow cats K&N Typhoon CAI RPM Motorsports of Garner, NC dyno tune (421 RWHP)

04-03-2015, 04:35 PM	#387
ZWA SS BowtieBelle's SS Drives: 2010 Camaro SS Join Date: Jan 2012 Location: Perry, ok Posts: 1,074	How much spacer would I need? Never shopped for them __________________ My Z/SS http://www.camaro5.com/forums/showthread.php?t=286858 .

04-03-2015, 11:16 PM	#388
ZWA SS BowtieBelle's SS Drives: 2010 Camaro SS Join Date: Jan 2012 Location: Perry, ok Posts: 1,074	I realize now they did .125" per side vs total toe on the rear. It's all a mess. __________________ My Z/SS http://www.camaro5.com/forums/showthread.php?t=286858 .

04-04-2015, 07:56 PM	#390
ZWA SS BowtieBelle's SS Drives: 2010 Camaro SS Join Date: Jan 2012 Location: Perry, ok Posts: 1,074	28 3/16 front 28 1/4 rear. Raising wouldn't bother me any. __________________ My Z/SS http://www.camaro5.com/forums/showthread.php?t=286858 .

03-31-2015, 05:58 AM	#381
Norm Peterson corner barstool sitter Drives: 08 Mustang GT, 19 WRX Join Date: Jul 2012 Location: Eastern Time Zone Posts: 6,990	As far as I know, camber specs have always been expressed in degrees. Norm

03-31-2015, 07:43 AM	#383
JusticePete Drives: Camaro Justice Join Date: Jun 2007 Location: Virginia Posts: 20,174	yep, degrees.

04-04-2015, 09:41 AM	#389
JusticePete Drives: Camaro Justice Join Date: Jun 2007 Location: Virginia Posts: 20,174	What is your ride height?

04-06-2015, 01:34 AM	#392
ZWA SS BowtieBelle's SS Drives: 2010 Camaro SS Join Date: Jan 2012 Location: Perry, ok Posts: 1,074	I measured from fender edge to the ground thru the centerline of the wheel. __________________ My Z/SS http://www.camaro5.com/forums/showthread.php?t=286858 .

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Definitive GT500 Thread	garagelogic	Chevy Camaro vs...	98	02-12-2010 01:14 PM
Lets start a Tire Specific Thread here, sizes, brands, specs and other usefull info.	55Designs	Wheels and Tires Talk Sponsored by The Tire Rack	0	12-20-2009 07:58 PM
Suggestion: Explanation to thread starters for their threads being locked?	colin911	Site Related Announcements / Suggestions / Feedback / Questions	2	12-06-2009 10:25 PM
Dealer Praise Thread (Not an Idiot!)	RPO_Z28	Camaro Price \| Ordering \| Tracking \| Dealers Discussions	84	06-25-2009 01:00 AM
prices thread	nimnels	5th Gen Camaro SS LS LT General Discussions	1	05-02-2009 06:47 PM