SS bumper cover installed on my 2LT/RS - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

01pewterz28 · 03-04-2010, 07:57 AM

***SS Bumper Cover conversion kit available from GMPartshouse http://www.camaro5.com/forums/showthread.php?t=123058

What it’s done it was a pain but if it was not for the two articles on Camaro5 on how to remove the bumper cover I would have paid the $200 and have the body shop do it. The install it took a total of 3 hours from start to finish (if I had a shop to do the work I think I could have cut the time down) I started just after 8pm last night and walked inside just after 11pm. My V6 bumper cover was hit a month ago by a piece of truck tire and put a scratch on the passenger side by the side marker the trucking companies insurance company sent me a check to repair the damage they figured $580 so I opted to buy a new bumper cover and have it painted. Here are some quick photos of the bumper cover installed (photos from my I phone better ones this weekend).

For anyone who is planning on doing this the V8 bumper bolts right up to car no issues you will need 4 extra parts from the parts department (cosmetic items only).

1. You will need to order the SS lower grille
2. SS mail slot grille
3. The rubber splash guard on the underside of the bumper cover the SS is 2” longer than the V6 one
4. When you open the hood on the edges of the bumper cover that are on top of the frame (where the GM Performance Parts division badge would be on the SS) is a plastic cover/strip that runs from one end of the bumper cover to the other you will need a new one of these to keep the bolts from rubbing into the plastic bumper cover (I will post pics)

You will need to remove the following items from the stock V6 bumper cover and move them over to the SS bumper cover.
1. Upper grille (they are held in with the stock push tabs)
2. Remove the middle plastic bumper support this attaches to the upper and lower grilles (keeps it in place)
3. Remove the side amber marker lights on each side of the bumper cover
4. Remove the fog lamp plastic liners
5. Remove the fog lamps
6. Remove the (6) 3 on each side mounting screw holders this is where the wheel liner screw into the bumper to secure it

The hardest part of taking off the bumper cover were the 3 bolts on each side of the fender The highest bolts on the sides that connect the bumper to the front quarter panels were a real pain because they are hard to get to if you have big hands forget about it. I would also suggest removing both front wheels to make it easier (you do not have to but it would make things go faster IMHO).

Good luck if you plan to do this I can say now that I have done it once I believe I can cut the time in half maybe 2/3’s for the time since I know what the heck I am doing and where all of the bolts are that need to be removed.

Complete List of OEM parts to do the Swap over from the LS/LT bumper to the SS bumper.

OEM SS Bumper cover P/N 92236547
OEM lower SS grille P/N- 92218015
OEM Mail slot grille P/N 92242525
OEM SS Front Air Dam Deflector Spoiler P/N-92234403
OEM-Bumper/Fascia Emblem P/N-92238867
OEM-Bumper/Fascia Emblem P/N-92238937

Good luck
Sean

ctk1 · 03-04-2010, 08:41 AM

Nice work! It looks really good.

Hylton · 03-04-2010, 08:43 AM

How much did those Brembos cost you?

2010 SSRS · 03-04-2010, 08:54 AM

Looks awesome, now you need a 6.2 under the hood,

mdinferno · 03-04-2010, 09:20 AM

01pewterz28, i completed the same swap last week. it wasn't that bad of challenge. Did you have to remove the rivets off the old bumper?

01pewterz28 · 03-04-2010, 10:22 AM

Quote:

Originally Posted by ctk1

Nice work! It looks really good.

Thanks

Quote:

Originally Posted by Hylton

How much did those Brembos cost you?

FREE well sort of I traded Fesler-Moss a few of my custom car show display stands

Quote:

Originally Posted by 2010 SSRS

Looks awesome, now you need a 6.2 under the hood,

Looking at a super charger for the V6

Quote:

Originally Posted by mdinferno

01pewterz28, i completed the same swap last week. it wasn't that bad of challenge. Did you have to remove the rivets off the old bumper?

Nope did not need to remove them.

Thanks
Sean

Bond · 03-04-2010, 10:59 AM

Quote:

Originally Posted by Bad Karma

+1 On the LS-3.

SirBrad · 03-08-2010, 06:11 PM

Looks pretty cool. I'm always going back and forth on what bumper cover I think looks better. The SS does look more muscular.

guiLT · 03-08-2010, 06:25 PM

Good idea! I haven't seen someone do that yet.

01pewterz28 · 03-09-2010, 08:21 AM

A few updated photos

LT5 John · 03-18-2010, 04:09 AM

Nice job, looks great!...

JoeP@TeamBeckyD · 03-18-2010, 04:56 AM

Looks great. First the brakes, now the bumper cover, engine next?

shad2009 · 03-18-2010, 06:21 AM

lookin good man

01pewterz28 · 03-18-2010, 06:45 AM

Quote:

Originally Posted by BeckyD@RodgersChevrolet

Looks great. First the brakes, now the bumper cover, engine next?

Who knows maybe a supercharger unless I came accross a great deal on a L99 or LS7

Quote:

Originally Posted by shad2009

lookin good man

Thanks

03-04-2010, 07:57 AM	#1
01pewterz28 #TeamBeckyD Drives: 2017 HBM 2SS Convertible A8 Join Date: Aug 2008 Location: Apopka, FL Posts: 10,496 View My Garage	SS bumper cover installed on my 2LT/RS *SS Bumper Cover conversion kit available from GMPartshouse http://www.camaro5.com/forums/showthread.php?t=123058 What it’s done it was a pain but if it was not for the two articles on Camaro5 on how to remove the bumper cover I would have paid the $200 and have the body shop do it. The install it took a total of 3 hours from start to finish (if I had a shop to do the work I think I could have cut the time down) I started just after 8pm last night and walked inside just after 11pm. My V6 bumper cover was hit a month ago by a piece of truck tire and put a scratch on the passenger side by the side marker the trucking companies insurance company sent me a check to repair the damage they figured $580 so I opted to buy a new bumper cover and have it painted. Here are some quick photos of the bumper cover installed (photos from my I phone better ones this weekend). For anyone who is planning on doing this the V8 bumper bolts right up to car no issues you will need 4 extra parts from the parts department (cosmetic items only). 1. You will need to order the SS lower grille 2. SS mail slot grille 3. The rubber splash guard on the underside of the bumper cover the SS is 2” longer than the V6 one 4. When you open the hood on the edges of the bumper cover that are on top of the frame (where the GM Performance Parts division badge would be on the SS) is a plastic cover/strip that runs from one end of the bumper cover to the other you will need a new one of these to keep the bolts from rubbing into the plastic bumper cover (I will post pics) You will need to remove the following items from the stock V6 bumper cover and move them over to the SS bumper cover. 1. Upper grille (they are held in with the stock push tabs) 2. Remove the middle plastic bumper support this attaches to the upper and lower grilles (keeps it in place) 3. Remove the side amber marker lights on each side of the bumper cover 4. Remove the fog lamp plastic liners 5. Remove the fog lamps 6. Remove the (6) 3 on each side mounting screw holders this is where the wheel liner screw into the bumper to secure it The hardest part of taking off the bumper cover were the 3 bolts on each side of the fender The highest bolts on the sides that connect the bumper to the front quarter panels were a real pain because they are hard to get to if you have big hands forget about it. I would also suggest removing both front wheels to make it easier (you do not have to but it would make things go faster IMHO). Good luck if you plan to do this I can say now that I have done it once I believe I can cut the time in half maybe 2/3’s for the time since I know what the heck I am doing and where all of the bolts are that need to be removed. Complete List of OEM parts to do the Swap over from the LS/LT bumper to the SS bumper. OEM SS Bumper cover P/N 92236547 OEM lower SS grille P/N- 92218015 OEM Mail slot grille P/N 92242525 OEM SS Front Air Dam Deflector Spoiler P/N-92234403 OEM-Bumper/Fascia Emblem P/N-92238867 OEM-Bumper/Fascia Emblem P/N-92238937 Good luck Sean Attached Images __________________ #TeamBeckyD FIFTY HBM 2SS VERT** Last edited by 01pewterz28; 11-18-2011 at 07:19 AM. Reason: added OEM P/N's

03-08-2010, 06:25 PM	#9
guiLT Tampa Gulf Coast Family Drives: 2001 Maxima Join Date: Oct 2009 Location: Tampa, Florida Posts: 6,585 View My Garage	Good idea! I haven't seen someone do that yet. __________________

03-09-2010, 08:21 AM	#10
01pewterz28 #TeamBeckyD Drives: 2017 HBM 2SS Convertible A8 Join Date: Aug 2008 Location: Apopka, FL Posts: 10,496 View My Garage	A few updated photos Attached Images __________________ #TeamBeckyD FIFTY HBM 2SS VERT

03-18-2010, 04:56 AM	#12
JoeP@TeamBeckyD Drives: SS,PaceCar,ZL1,1LE,C7Z51,Z06,17-ZL1 Join Date: Jun 2009 Location: Detroit, Mich Posts: 68,623	Looks great. First the brakes, now the bumper cover, engine next? Attached Images

03-18-2010, 06:21 AM	#13
shad2009 "Cassie" Drives: 2007 Tungsten Grey Mustang GT Join Date: Sep 2009 Location: Massachusetts Posts: 1,153	lookin good man __________________ Currently driving - 2007 Mustang GT Future Wheels - 2014 Ford Mustang GT & 2014 Chevy Camaro

03-04-2010, 08:41 AM	#2
ctk1 Camarofanatic Drives: 1969 SS, 1998 RS, 2010 VR 2SS/RS Join Date: Sep 2008 Location: Gallitzin PA Posts: 1,433	Nice work! It looks really good.

03-04-2010, 08:43 AM	#3
Hylton Drives: fanboys and ass kissers crazy. Join Date: May 2008 Location: Ottawa, Ontario Posts: 7,280	How much did those Brembos cost you?

03-04-2010, 08:54 AM	#4
2010 SSRS Drives: 3 V8 Camaros Join Date: May 2009 Location: The Ocean State Posts: 111,187 View My Garage	Looks awesome, now you need a 6.2 under the hood,

03-04-2010, 09:20 AM	#5
mdinferno Drives: 2010 IBM 2LT/RS Join Date: Dec 2009 Location: MD Posts: 1,636	01pewterz28, i completed the same swap last week. it wasn't that bad of challenge. Did you have to remove the rivets off the old bumper?

03-08-2010, 06:11 PM	#8
SirBrad The Captain Drives: 2010 2LT/RS SIM Join Date: May 2009 Location: Freehold, NJ Posts: 1,499	Looks pretty cool. I'm always going back and forth on what bumper cover I think looks better. The SS does look more muscular.

03-18-2010, 04:09 AM	#11
LT5 John Drives: 2010 RS/2LT Camaro / 2008 C6 Z06 Join Date: Mar 2010 Location: Port St Lucie, FL Posts: 30	Nice job, looks great!...

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
MBRP Exhaust Installed on my 2LT/RS	DevilKnightFalcon	Camaro V6 LLT Engine, Exhaust, and Bolt-Ons	47	05-30-2012 11:56 PM
Do you want the Z28?	ChrisB	Camaro ZL1 Forum - ZL1 Specific Topics	1616	09-04-2010 11:49 PM
WTB front bumper ss or v6	ss1_2010	Exterior Parts & Accessories	4	08-21-2010 11:46 PM
SS front bumper on a LS?	FutureCamaroOwner	5th Gen Camaro SS LS LT General Discussions	10	12-20-2009 11:31 AM