help with rear valance removal!! - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

tytus03 · 07-23-2010, 10:13 AM

can anyone help me with getting off the rear plastic valance or whatever its called that goes around the muffler tips and what-not?

thanks

Michael_Js · 07-23-2010, 10:46 AM

These are posted elsewhere, but maybe they can help:

tytus03 · 07-23-2010, 11:03 AM

Quote:

Originally Posted by Michael_Js

These are posted elsewhere, but maybe they can help:

thanks a lot, that does get me a bit closer. I guess its just the diffuser that i'm needing to remove so i can do an exhaust swap. still not sure if i need to do all the steps in those instructions though.

Blackbean · 07-23-2010, 05:33 PM

I think there are 4 screws underneath and the rest of it snaps in along the top edge.

SSTony · 07-27-2010, 08:37 PM

you need to remove the rear bumper to remove the valance

henchmen3 · 07-28-2010, 11:48 PM

all you need to do is take off the 2 7mm bolts that hold the edges to the rear bumper and then the 4 10mm bolts accross the bottom. Once those 6 bolts are off, start at one end and pull out. It is only held in place with push type pins. I did it and its not hard, no need to remove the whole tail section.

SSTony · 07-29-2010, 10:20 PM

i tried to pull mine off and it just would not snap out.

SILVER BULLITT · 08-06-2010, 01:32 AM

its a pain to get them to snap sometimes

apace0509 · 09-27-2013, 12:14 PM

need help on how to replace rear valance on 2011 camaro 2ss do i have to remove the rear fascia or just the 6 screws that hold the valance on underneath

hworth18 · 09-28-2013, 03:41 PM

There is a DIY on how to remove the rear diffuser. I used it and it worked pretty good.

http://www.camaro5.com/forums/showthread.php?t=153221

07-23-2010, 10:13 AM	#1
tytus03 Account Suspended Drives: F150/2010 camaro 2ss blk ls3 Join Date: Jul 2010 Location: south texas Posts: 43	help with rear valance removal!! can anyone help me with getting off the rear plastic valance or whatever its called that goes around the muffler tips and what-not? thanks

07-23-2010, 10:46 AM	#2
Michael_Js SoCal C5 Family Member Drives: 2010 Camaro SS/RS - Black w/IOM; 6M Join Date: Jul 2009 Location: San Diego, CA, USA Posts: 5,299 View My Garage	These are posted elsewhere, but maybe they can help: Attached Images __________________ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~ 2010 Black 2SS/RS; 6M; IOM, GFX, sunroof; ADM Race CAI; Zoomers CB; Viper Alarm; Pdaft F&R sways, Adj Endlinks, Rtrailing arms, Camber kit, strut brace, Front Trailing Arm Bushing; SLP Skip-Shift Elim; Tinted lights/windows; Hurst Short-throw; LoJack; Door & Dash ABL Mods; ********; JBA Shorty headers; AACStyle LEDs; Stillen DS rotors, Hawk Ceramic pads; Havoc Blk Chrome wheels: 20x9s; Lingenfelter Blk Al Pedals; RevXtreme Catch Can; Goodridge SS lines; Ported TB; RK Sport hood; Hotchkis chassis brace; KW V3 coilovers;

07-27-2010, 08:37 PM	#5
SSTony Drives: SS Camaro Join Date: Jul 2009 Location: Piscataway NJ Posts: 1,782 View My Garage	you need to remove the rear bumper to remove the valance __________________

07-29-2010, 10:20 PM	#7
SSTony Drives: SS Camaro Join Date: Jul 2009 Location: Piscataway NJ Posts: 1,782 View My Garage	i tried to pull mine off and it just would not snap out. __________________

08-06-2010, 01:32 AM	#8
SILVER BULLITT Drives: 2010 SIM 2SS/RS MONSTER Join Date: Aug 2009 Location: LOS ANGELES Posts: 1,506 View My Garage	its a pain to get them to snap sometimes __________________ HP MONSTER' SOUTHERN CALIFORNIA BUILT, LMR CAI, CUSTOM GRIND CAM, CUSTOM BUILT CNC PORTED AND POLISHED HEADS, FAST 102MM INTAKE MANIFOLD,ARH LONG TUBES AND HIGH FLOW CATS, BIGGER INJECTORS, VALVES SPRINGS RETAINERS, MGW SHORT SHIFTER, EIBACH SPRINGS, FACTORY CHROMED WHEELS, BLACKED OUT EMBLEMS, BLACKED OUT ROOF,BLACKED OUT MARKERS, 3.5 INCH ELECTRONIC CUTOUTS, FLOWMASTERS, ZEX WET 150 SHOT, FOR A GRAND TOTAL OF =630 REAR WHEEL TORQUE ,AND 600 REAR WHEEL HORSEPOWER MY JOURNALhttp://www.camaro5.com/forums/showth...02#post2023802 SOON TWIN TURBO SETUP

07-23-2010, 05:33 PM	#4
Blackbean Drives: 2018 1SS 1LE Join Date: Feb 2010 Location: San Antonio, Fl Posts: 168	I think there are 4 screws underneath and the rest of it snaps in along the top edge.

07-28-2010, 11:48 PM	#6
henchmen3 Drives: 2010 all white Join Date: Jun 2010 Location: Maryland Posts: 71 View My Garage	all you need to do is take off the 2 7mm bolts that hold the edges to the rear bumper and then the 4 10mm bolts accross the bottom. Once those 6 bolts are off, start at one end and pull out. It is only held in place with push type pins. I did it and its not hard, no need to remove the whole tail section.

09-27-2013, 12:14 PM	#9
apace0509 Drives: 2011 camaro 2ss rs package Join Date: Sep 2013 Location: canton ohio Posts: 1	rear valance need help on how to replace rear valance on 2011 camaro 2ss do i have to remove the rear fascia or just the 6 screws that hold the valance on underneath

09-28-2013, 03:41 PM	#10
hworth18 Jus' Cruzin Drives: 2017 Camaro 1SS Krypton Green Join Date: Oct 2012 Location: Northeast Oklahoma Posts: 1,108 View My Garage	There is a DIY on how to remove the rear diffuser. I used it and it worked pretty good. http://www.camaro5.com/forums/showthread.php?t=153221 __________________ “The moment you think you know what’s going on in a women’s head, is the moment your goose is well and truly cooked” -Howard Stark

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Modifying for " Dummies"	Dr Jkel	Tuning / Diagnostics -- engine and transmission	209	06-17-2012 11:24 PM
Setting up an IRS/Drivetrain for Drag Racing	Kyle2k	Suspension / Brakes / Chassis	44	06-05-2010 09:17 PM
Rear strut removal??	Blown355	Suspension / Brakes / Chassis	2	05-11-2010 09:40 PM
Rear Speaker removal	SSinthedesert	Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum	7	03-29-2010 06:43 PM
Suspension guys out there - lets talk wheel hop	Crowley	Suspension / Brakes / Chassis	14	10-09-2009 12:06 AM