Do I need this upgrade? TVS 2300 - Page 2 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Nutro · 12-23-2013, 12:06 PM

How much is the FPCM from ADM?

1bad1le · 12-23-2013, 12:37 PM

Quote:

Originally Posted by Nutro

How much is the FPCM from ADM?

http://www.admperformance.com/produc...84&product=257

Big C CamaroSS · 12-23-2013, 12:44 PM

Quote:

Originally Posted by lincoln361

I was thinking about the getting the ADM Fuel pump booster. It doesnt seem to hard to install, the MSD 2351 looks a little more difficult to install. Which one do you have?

I have the MSD fuel pump voltage booster. I bought it from Jannetty Racing. My buddy had to splice 2 wires and then I ran the vacuum line to the supercharger. I have the 1LE (which comes withe the ZL1 fuel pump) so the Fuel pump voltage booster is insurance. Best thing to do is get a hold of Ted Jannetty

lincoln361 · 12-23-2013, 03:38 PM

Quote:

Originally Posted by Nutro

How much is the FPCM from ADM?

Ordered mine today. Should get it to me by tomorrow. Real nice guy and knowledgable. Even gave me a military discount.

lincoln361 · 12-23-2013, 03:40 PM

Quote:

Originally Posted by BlownSS

The ADM FPCM controls the ZL1 pump and tells it what to do. ......the BAP increases the voltage to increase the output of fuel. I am running both and am getting enough fuel for 650 rwhp through 850 cc injectors at about a 70-80% duty cycle.

What about the ZR1 Maf sensor? Should i be getting that as well when im doing all this as well? My numbers wont even be close to your but its a start ha ha. I dont think i will be get a BAP yet from what Andy from ADM is saying since i wont be pushing that much horsepower.

Piccione Performance · 12-23-2013, 05:52 PM

I would do the ADM module with your current collection of parts, have it tuned properly and you will be fine with your current set up.

lincoln361 · 12-24-2013, 12:07 PM

Yeah I ordered it. Their is a lot of good stuff about so I am going to give it a shot

victoryred1ss · 12-24-2013, 12:25 PM

I wouldnt waste your time with 65lb injectors. Keep the stock maggie injectors for the 3.6 pulley and when you really want to make power put some ID850 injectors, raise the boost and change your camshaft.

12-23-2013, 12:06 PM	#15
Nutro Drives: 2011 2SS Synergy Green Join Date: Nov 2011 Location: Austin, Texas Posts: 3,670	How much is the FPCM from ADM? __________________ L99 With a Maggie

12-24-2013, 12:07 PM	#21
lincoln361 Drives: 2011 Camaro SS/RS Join Date: Feb 2011 Location: corpus christi tx Posts: 1,046 View My Garage	Yeah I ordered it. Their is a lot of good stuff about so I am going to give it a shot __________________ SLP TVS 2300- 1 7/8 LG Headers- RDS NX Plate- 75 Shot- No Cats- SLP Loudmouth 2- NW102- 3.8 Pulley- OD Cog drive-12lbs boost-FIC 80# injectors-ZL1 Fuel Pump- RotoFab CAI- Apex CAI Scoop- Pat G Tune- Weld RTS drag pack- BMR Trailing Arms- BMR 1'' Drop Springs-BMR Lower Control Arms- BMR Toe Rods- BMR Rear Cradle Bushings- BMR Upper Control Arm Bushings- BMR Extreme Anti- Rollbar- Hotchkis Subframe Brace- Prosport Evo Boost & F/A Ratio

12-24-2013, 12:25 PM	#22
victoryred1ss Drives: 2010 SS M6 2016 2SS A8 Join Date: Oct 2009 Location: Utah Posts: 553	I wouldnt waste your time with 65lb injectors. Keep the stock maggie injectors for the 3.6 pulley and when you really want to make power put some ID850 injectors, raise the boost and change your camshaft. __________________ TVS 2300 721RWHP 686RWTQ Built by Me Suspension done by JDP Tune done by JRE

12-23-2013, 05:52 PM	#20
Piccione Performance Drives: 2010 2ss/rs & 2014 Stingray Join Date: Aug 2013 Location: Phoenix Posts: 124	I would do the ADM module with your current collection of parts, have it tuned properly and you will be fine with your current set up.